Walkway Cover Archives

How To Use Master Plans – TER’s – Calculator Reports Purchased From Engineering Express

READ BELOW BEFORE USING NON SITE-SPECIFIC PERFORMANCE EVALUATIONSFROM ENGINEERING EXPRESS FOR YOUR PROJECT General Information About Non Site-Specific Plans: Certified Performance Evaluations (also referred to as Master Plans, Generic, or Non Site-Specific Plans) you receive contain a physical or digitally certified engineer seal. They are intended to be used to assist in obtaining a building …

How To Use Master Plans – TER’s – Calculator Reports Purchased From Engineering Express Read More »

Why are spacing, edge distance, and embedment important for concrete anchors?

When an anchor is installed into concrete, there is an area surrounding the anchor called a cone of influence in which the anchor is affecting and it is affected by. When two anchors are spaced too closely to one another and/or too closely to an edge, the anchor’s cone of influence reduces or becomes interfered …

Why are spacing, edge distance, and embedment important for concrete anchors? Read More »

How To Determine Uplift Reactions For Canopies-Carports-Pergolas

Canopies & Wind Understand this – A backyard canopy attached to the back of your house, a pergola/trellis, or a lightweight sunroom/screen room comprise of relatively very little weight and is of lesser construction than the structure to which they are attached. Also, consider that a wall of a house continuously supports a roof, …

How To Determine Uplift Reactions For Canopies-Carports-Pergolas Read More »

What wind information is required for construction documents?

From the 5th, 6th &7th Edition of the Florida Building Code (2014, 2017, 2020) section 1603.1.4 as well as from section 1603.1.4. of the 2012, 2015, & 2018 International Building Code, construction documents shall show the following: Ultimate design wind speed, Vult (3-second gust), miles per hour and nominal design wind speed (Vasd) as …

What wind information is required for construction documents? Read More »

Wind Speed to Wind Pressure For Sunrooms – Canopies – Pergolas Using ASCE 7-16

ASCE 7-16 is introduced into the 2018 International Building Code and 7th Edition Florida Building Code (2020) as the new referenced standard for wind design. This standard introduced an enhanced section for the conversion of wind velocities to roof wind pressures for roof components attached to buildings and freestanding structures such as sunrooms, overhead canopies, …

Wind Speed to Wind Pressure For Sunrooms – Canopies – Pergolas Using ASCE 7-16 Read More »

Wind Speed vs. Wind Pressure Explained

Many don’t understand how wind works & state that a product is rated to a specific wind speed. This is false advertising & not true. There’s no such thing as “Rated to XXX MPH wind” This is frequently seen in marketing materials which is a false & misleading statement that comes with many unwritten …

Wind Speed vs. Wind Pressure Explained Read More »

TEK Sheet Metal Screws (SMS) – About – Sizes – Gauges

About TEK Screws The following information is complied compliments of All Points Fasteners, Totally Nuts And Bolts, and Fastenermart Tek® screws, which is a brand name describing self-tapping fasteners, have a very small carving at the end of its tip called a drill bit. This particular product is very popular since it is basically a self drilling product …

TEK Sheet Metal Screws (SMS) – About – Sizes – Gauges Read More »

Where To Buy Extrusions & Parts

We’re frequently asked by our clients where they can purchase many of the products specified in our plans. Below is a growing list of products1 for your reference. FEATURING PRODUCTS BY: CLICK ON THE LINKS BELOW TO FIND THE PRODUCT(S) YOU ARE LOOKING FOR: General Extrusions Eastern Metal Supply Standard Extrusion & Sheet Products Eastern …

Where To Buy Extrusions & Parts Read More »

Procedure For Calculating Aluminum Box Beams For Bending

Per the Aluminum Design Manual (ADM) 2015, the allowable bending stress of round tubes shall be determined for the limit states of yielding, rupture, and local buckling: that given by section F.6.1 (compressive yielding), or that given by section F.6.1 (tensile yielding), or that given by section F.6.1 (tensile rupture), or that given by …

Procedure For Calculating Aluminum Box Beams For Bending Read More »

Cookie	Duration	Description
cookielawinfo-checkbox-analytics	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Analytics".
cookielawinfo-checkbox-functional	11 months	The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional".
cookielawinfo-checkbox-necessary	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookies is used to store the user consent for the cookies in the category "Necessary".
cookielawinfo-checkbox-others	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other.
cookielawinfo-checkbox-performance	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Performance".
viewed_cookie_policy	11 months	The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. It does not store any personal data.