Performance Limitations for Mechanical Equipment & TER Certifications
Summary of Building Code & Research Intent The intent & provisions of the 2018 International Building Code (IBC), 2018 International Residential Code (IRC) & 2020
Providing resources to help in design & permitting for stands & wall mount brackets manufactured by Miami Tech, Inc.
Quick Links
Certified Plans For Permit
Purchase engineer-certified digital or hardcopy evaluation reports to submit for permit.
Miami Tech: Mechanical Unit Steel Tie-Down Clips (MPS 20-26324)
$6.00 – $16.00
or ( 0.5 Tokens – 1.5 Tokens )View
Miami Tech Design Aids
Use these for estimating & to interact with an engineer to develop certified plans for permit for your AC stand need.
Helpful Articles for Permitting
About Impact Requirements & Mechanical Equipment in the Florida Building Code & Essential Facilities
Mechanical Equipment – Impact or Not Impact? Questions frequently arise as to what the rule is in Florida, Miami, and the HVHZ zone (Dade and
Pros and Cons of Obtaining a Florida Statewide Approval Vs A Miami Dade Approval and how a TER fits in
Two common means of product evaluations in Florida are Florida Statewide Approvals (FSA’s) and Miami-Dade Notices of Acceptance (NOA’s). To help determine whether these evaluations
How Do I Get Approval To Substitute Glass Type-Interlayer On My Product Evaluation?
If you are a manufacturer with a Florida or Miami Dade Approval, or if you are trying to install a tested and approved large missile
Search our AC model Database
Click Here to access our model database tool. You can filter by your AC brand, model, and number to find the TER report you need
AC Model TER Search Database
Use this tool to search and find the applicable Technical Evaluation Report for your installation.
I see values for F1 and F2 on Evaluation Reports. What are they?
F1 and F2 are the limiting performance capacities of the forces in the parallel and perpendicular directions of a building component. Which one is which
How To Use Master Plans – TER’s – Calculator Reports Purchased From Engineering Express
READ BELOW BEFORE USING NON SITE-SPECIFIC PERFORMANCE EVALUATIONSFROM ENGINEERING EXPRESS FOR YOUR PROJECT General Information About Non Site-Specific Plans: Certified Performance Evaluations (also referred
What are editorial changes to products registered in the Florida Product Approval System?
Editorial changes are permitted within the state product approval system when an approved product is modified but no additional uploads are needed, and there is
I need to create an NOA / product approval for my product. What’s the process?
Start by reading our articles about product approvals by Clicking Here. You’ll learn when they’re really needed, what information we need, how they help, and
Can you help me with Florida Product approval or Miami Dade NOA information?
If you need to find a Florida Approval number please visit https://floridabuilding.org/pr/pr_app_srch.aspx For a Miami Dade NOA please visit http://www.miamidade.gov/building/pc-search_app.asp
Learn About Rooftop & Ground Wind Forces for Mechanical Units
Want to learn how to design AC units on stands or curbs for wind design? Are you looking for tools to help in in design?
About Door Product Pressure Ratings and Water Infiltration
QUESTION: Why do certain door products rate a certain p.s.f like -60/+60 then lower ratings are shown throughout the product approval? Usually, the higher
Instructions for proper use of rooftop equipment wind pressure calculator
HELP PAGE For the Engineering Express® Rooftop Equipment Wind Pressure Calculator Note: See Limitations & Conditions of Use at the end of this article. Quick
What are Limitations of Small & Large Missile Impact Designs?
We are frequently asked what are the limitations applied on Small Missile Impact and Large Missile Impact products. Engineering Express takes into consideration the following
What are the requirements for using ASTM Missile Level E in Florida (2021 updated)?
In the 7th Edition Florida Building Code (2020), missile level E is valid in and outside of the HVHZ (Broward and Dade Counties) when it
Is a large missile impact window or door automatically approved for small missile impact?
Overview Changes to the 2020 Florida Building Code for Porous Impact Protection Devices Porous Impact Protective Systems: ASTM E1996-12A brought a significant change to Porous
Miami Dade NOA Revision vs Renewal & Fees Explained
As of January, 2021, here is an explanation from Miami Dade County’s Product Approval System (Product Control) on the differences, timeframes, and fees for their
What wind information is required for construction documents?
From the 5th, 6th &7th Edition of the Florida Building Code (2014, 2017, 2020) section 1603.1.4 as well as from section 1603.1.4. of the 2012,
Can you substitute spacers for insulating glass units (IGU)?
The question of whether or not an installer can substitute the spacer that separates the outer from the inner glazing on an insulating glass unit